UPSB v3

Approved Tutorials / Simple Clear body Dr.KT tutorial

by K4S

  1. K4S
    Date: Sat, Oct 6 2007 02:41:47

    Welcome to the Simple Clear body Dr.KT tutorial!

    A mini tutorial by me, K4S smile.gif

    I've seen many threads asking how to make a clear Dr.KT and the answer to that question is either find clear keityo or find a persons's pens or find pen XYZ etc, all of which are generally rare or difficult to get. This tutorial will provide an effective and simple solution to making a Clear Dr.KT.

    I've known about this for a long time, sorry, one of the many mini mods & variations to be forever stored in my secret box of pen mods ph34r.gif But it's thanksgiving weekend and I had some time to spare so I decided to make this tutorial.

    I never realised until I measured it but this mod (if made correctly) is 0.1mm longer than a real Dr.KT. As well, the diameter of a Keityo barrel (measured in the middle of the body) is 9.75mm and the "substitute" barrel (measured from the middle of the body) is 9.70mm, so you cynics don't have much to complain about, mmmkay?

    Stats:
    -pretty much the same as a Dr.KT happy.gif


    So let us begin�

    1.
    You will need:
    1x bare rsvp barrel
    2x rsvp back caps
    2x pre-made Dr.KT caps (Keityo + sailor grips + dr.grip tip)

    2.
    Get the rsvp body and follow the directions on the picture. The bottom rsvp body is what it should look like once cut, and make sure you get it under 0.6cm (0.5cm will do) or else the back cap wont fit on it properly.



    3.
    The cap should be very snug. It should not be able to wiggle around.


    4.
    The order in which to do the following has been numbered 1-4, you can follow along, right?



    Final Product!

    Close up of insert 1
    Close up of insert 2





    Trouble Shooting Questions:
    Q: I screwed on the back cap on the side with tape, put the dr.KT cap on, but when I went to take the Dr.KT cap off the rsvp back cap got pulled out as well and is stuck inside the Dr.KT cap. How do I get it out?
    A: Take another rsvp body, screw on the body to the back cap stuck in the dr.KT cap and then pull it out.

    Q: How durable is the side where the back cap screws onto tape?
    A: Durable enough for regular spinning unless you plan to practice leguining it against a wall.

    Q: wtf, secret box of mods?
    A: Uh huh, I'll release some of the stuff I have in there eventually...maybe ._.

    Q: Thank you!
    A: Not a question, but you're welcome happy.gif

    A: The answer is, This is awesome!�
    Q: What is a clear body dr.KT� tutorial? /vain

    Q: Post your insert NAO!!!!!
    A: *cries* ALL YOU PEOPLE WANT IS MORE MORE MORE MORE MORE *sobs* LEAVE ME ALONE *cries* YOU�RE LUCKY I EVEN MADE THIS TUTORIAL FOR YOU BASTARDS! *cries some more* LEAVE ME ALONE *cue more crying*

  2. nateiskewl
    Date: Sat, Oct 6 2007 02:47:57

    Making it now. Thanks K4S! happy.gif

  3. Foofdude
    Date: Sat, Oct 6 2007 02:50:41

    That's really cool. I would have never thought of using an RSVP for the body.

    You could just use a ballsign body though. I think that's what most people who have clear KTs use.

  4. Reminiscent
    Date: Sat, Oct 6 2007 02:52:05

    That's wicked O_O Thanks K4S.

    LMFAO @ your Chris Crocker quote xDDDD

  5. Aries
    Date: Sat, Oct 6 2007 06:05:21

    WTF it uses 9 pens for this mod if im counting correctly...

  6. K4S
    Date: Sat, Oct 6 2007 06:16:59

    Yep, 9 pens. However, Dr.KT uses 7 pens, so if you look at it from that point of view my little variation for a clear body only uses an extra 2 rsvp which is only $2 extra.

  7. Sfsr
    Date: Sat, Oct 6 2007 11:49:58

    Awesome K4S, especially since the caps don't actually have to be Dr. KT caps (I mean one can as well use KT caps with G-1 tips, just grips, etc).

    Question though, wouldn't there be more weight in the body here then on a regular KT?

  8. longhorn
    Date: Sat, Oct 6 2007 13:29:48

    I was made this mod before you post this topic but not like this I just cut a little bit place of rsvp plastic tip off.


    I love this mod so much




    I always like this insert. Can you post it??

    please

  9. Jamie Enns
    Date: Sat, Oct 6 2007 17:46:08

    W00T!!
    I love you!
    so what do i call a mod with Dr.St caps, rsvp body, and Aspire tips? its no longer anything "Dr" or "KT"

    THANKS

  10. K4S
    Date: Sat, Oct 6 2007 18:55:00

    @Sfsr: Yeah, i suppose the rsvp body might weight slightly more than a KT body but i dont think its much different. When i have the opportunity i'll try to weight them both.

    @Jamie: Im not really sure what you would call it tongue.gif


    Also, if you dont put tape on the rsvp back caps you can jam on comssa caps (they wont completely cover the back caps) and have a clear body comssa. However, its ~1cm shorter than an a real comssa but it doesnt have the cut in the middle like the HGG clear comssa version.

  11. oshizitsrohiz
    Date: Sat, Oct 6 2007 19:43:09

    Q: Post your insert NAO!!!!!
    A: *cries* ALL YOU PEOPLE WANT IS MORE MORE MORE MORE MORE *sobs* LEAVE ME ALONE *cries* YOU’RE LUCKY I EVEN MADE THIS TUTORIAL FOR YOU BASTARDS! *cries some more* LEAVE ME ALONE *cue more crying*
    [/quote]

    lol that britney spears fan guy was really fricking insane... nice mod btw. Keep up the good tutorials. groucho.gif

  12. Sfsr
    Date: Sat, Oct 6 2007 20:00:11

    My KT caps stay on more then good without taping the backplugs ^^

  13. K4S
    Date: Sat, Oct 6 2007 20:03:24

    QUOTE (Sfsr @ Oct 6 2007, 04:00 PM) <{POST_SNAPBACK}>
    My KT caps stay on more then good without taping the backplugs ^^

    Yeah, the tape is more of a precautionary measure, especially for spinners who can spin crazy fast like Donza. After all, you dont want dr.KT caps flying off...been there, done that and results are usually bad tongue.gif

  14. Sfsr
    Date: Sat, Oct 6 2007 20:11:48

    Liek here :D

    And I've just tested spinning with regular gripped KT caps, if there are Dr Grip tips attached to them, I guess they would fly of more easily.

    EDIT: disabled smileys >__>

  15. Zest
    Date: Sun, Nov 11 2007 02:17:28

    nice idea. i thought of that already too.

  16. Radiance
    Date: Mon, Nov 12 2007 18:44:34

    i'm makin this mod right now but with sharpie caps. i was wondering if i should cut the top wer the little knob is...like in pholord's Dr. ST mod.

    just making sure becuz i only have 2 harpie caps left dry.gif

    Edit:
    IMAGE

  17. asian
    Date: Mon, Nov 12 2007 19:14:43

    QUOTE (Radiance @ Nov 12 2007, 01:44 PM) <{POST_SNAPBACK}>
    i'm makin this mod right now but with sharpie caps. i was wondering if i should cut the top wer the little knob is...like in pholord's Dr. ST mod.

    just making sure becuz i only have 2 harpie caps left dry.gif


    do you mean cut where the metal thingy is??

  18. melvenorc12
    Date: Mon, Nov 12 2007 21:29:06

    Thank you for this mod, its great! happy.gif

    I used a back cap with a drilled hole and used the ink tube from a Pilot Dr. Grip to make it a writable pen.

  19. Xero
    Date: Sat, Jan 12 2008 03:17:09

    How does the weight compare to that of a normal Dr. KT?

  20. Crzyazn
    Date: Sat, Jan 12 2008 04:11:10

    *searches drawer of pens for a bit*
    *rejoices as two once broken RSVP MXs are found*
    *makes mod*

  21. SS4_Flames
    Date: Wed, Jan 16 2008 00:50:07

    So this is what was on PenWish, can someone upload the insert he used?

  22. Sfsr
    Date: Wed, Jan 16 2008 17:16:54

    Afaik, there are more then one version up on PW, and the inserts he uses aren't released. You should be able to find something suitable in the "Show Your Inserts" thread though.

  23. SS4_Flames
    Date: Thu, Jan 17 2008 23:02:33

    I meant the RIP bonkura insert K4S used. I already looked through most the insert thread though.

  24. darkeh
    Date: Fri, Jan 18 2008 00:08:30

    QUOTE (K4S @ Oct 5 2007, 09:41 PM) <{POST_SNAPBACK}>
    Q: Post your insert NAO!!!!!
    A: *cries* ALL YOU PEOPLE WANT IS MORE MORE MORE MORE MORE *sobs* LEAVE ME ALONE *cries* YOU�RE LUCKY I EVEN MADE THIS TUTORIAL FOR YOU BASTARDS! *cries some more* LEAVE ME ALONE *cue more crying*

    Here it is ^^ lol jk

  25. sillychicken
    Date: Thu, Jan 24 2008 23:00:22

    mazing tut, mazing mod biggrin.gif

  26. Teddy
    Date: Sat, Jan 26 2008 22:26:08

    it's really sturdy if you just hot glue the other back cap on

    i mean like... uber sturdy. i can't even get it off with a pliers

  27. Jack
    Date: Sun, Feb 3 2008 03:52:20

    thx for the tut! i made it with expo caps instead cuz im 2 lazy to buy new pens.

    Edit: made a real one. i love the feeling of the rsvp barrel, thx. biggrin.gif

    Edit edit: if you use regular old paper rolled up it works fine!

  28. servantofGod
    Date: Fri, Apr 11 2008 03:06:54

    yea I am ordiering a kt from penwish for caps and I have made a barrell like this. I think I will drill holes in the tips and make it write like a bictory

  29. Invincibleman
    Date: Fri, Apr 11 2008 03:31:14

    this is a good American substitute if you use sharpies

  30. Teddy
    Date: Fri, Apr 11 2008 04:13:08

    jw but what is the best way to keep the back cap on?

    i tried tape, teflon tape, hot glue, and even gorilla glue, but it always comes off

    then darkeh sent me a clearbody kt that was perfect.

    so what is the best?

  31. xxdefinitionxx
    Date: Fri, Apr 11 2008 04:26:29

    teddy, use superglue.....DUHH

    the one i use is called dr bond

    and they only try to intimidate u with that "bonds to skin in seconds! achtung!" crap it comes off in 2 days..

  32. Guitrum
    Date: Fri, Apr 11 2008 06:20:39

    haha that is exactally what i did before i saw this tutorial tongue.gif

  33. Thnikkaman
    Date: Sun, Apr 27 2008 16:55:37

    a great way to hold the back cap on is by:

    1-put a tiny bit of superglue on the plastic part where you put the back cap on

    2-wrap paper around where you just put the superglue and apply more superglue as you wrap the paper around

    3- apply enough paper so the back cap fits snugly

    i reccomend testing the paper under the back cap before you put the superglue. then you know how much paper you need.

    the main reason for this is so you can actually screw off the back cap. MAKE SURE YOU DON'T APPLY SUPERGLUE TO THE OUTERMOST LAYER OF PAPER!!!!!!!!!!! YOU DONT WANT THE BACK CAP TO BE STUCK, YOU WANT IT TO SCREW OFF!!!!!!! Or at least me because i put inktubes in.

  34. Blaze
    Date: Thu, Jun 5 2008 16:23:23

    I will make that one too biggrin.gif I've got some spare RSVP's but i think i'll use Comssa Caops with Dr.Grip Tips and Grips

  35. bigschlang31
    Date: Thu, Jun 5 2008 17:17:38

    where do u get the premade KT caps?

  36. K4S
    Date: Thu, Jun 5 2008 17:42:09

    QUOTE (bigschlang31 @ Jun 5 2008, 01:17 PM) <{POST_SNAPBACK}>
    where do u get the premade KT caps?

    From another dr.KT/CT/M&M (and unless you're buying them, you generally make it yourself)

  37. pen_MAKer
    Date: Thu, Jun 5 2008 18:44:59

    is it the same size as normal kt?

  38. Kool spinz
    Date: Fri, Jun 6 2008 10:19:53

    um the pen is nice but still have disadvantage . we can mod that , but still we need kt's cap from KT . so we better use comssa caps instead kt' caps

  39. iamk34n3
    Date: Fri, Jun 6 2008 17:44:18

    If you put comssa caps on the clear body, you will have absolutely NO momentum and it will suck to spin. wink.gif

  40. CaliMartinio
    Date: Fri, Jun 6 2008 18:13:03

    Comssa caps wont fit onto the backplug of the RSVP
    unless you want it half only and slightly bent

  41. ehntoo
    Date: Fri, Jun 6 2008 18:26:20

    I just built one and I'm in love. smile.gif

    Thanks K4S

  42. Kool spinz
    Date: Fri, Jun 6 2008 22:22:18

    QUOTE (CaliMartinio @ Jun 7 2008, 01:13 AM) <{POST_SNAPBACK}>
    Comssa caps wont fit onto the backplug of the RSVP
    unless you want it half only and slightly bent


    no need to be like that , just sand off/ file the rsvp backslugs until the comssa caps fit

  43. SevinosI
    Date: Sat, Nov 1 2008 18:23:40

    wow thanks man i been makin rsvp mods and i keep having left over bodies now i can use them laugh.gif

  44. dEViLoFmE
    Date: Mon, Nov 3 2008 00:23:51

    @Step 2 of the tutorial: It says on the picture that the part after it has been cut is 0.6cm,but what K4S wrote was 0.6mm.
    Correction? 0.6cm = 6mm.

    Please dont flame me if i see wrongly.
    I really liked this tutorial and i will try out this mod one day. biggrin.gif
    I see too many good comments.xD

  45. K4S
    Date: Mon, Nov 3 2008 04:05:04

    QUOTE (dEViLoFmE @ Nov 2 2008, 07:23 PM) <{POST_SNAPBACK}>
    @Step 2 of the tutorial: It says on the picture that the part after it has been cut is 0.6cm,but what K4S wrote was 0.6mm.
    Correction? 0.6cm = 6mm.

    Ahh, you are correct, it is supposed to be 0.6cm, not mm. I have fixed my tutorial, thanks.

  46. DarreN
    Date: Mon, Nov 3 2008 04:16:18

    QUOTE (Kool spinz @ Jun 7 2008, 06:22 AM) <{POST_SNAPBACK}>
    no need to be like that , just sand off/ file the rsvp backslugs until the comssa caps fit


    well for me i just remove the rsvp backplug , add tape on the screw threads and fit comssa cap on
    instead u saved up on a backplug

  47. Take-a-chill-pill
    Date: Sun, Nov 9 2008 18:32:36

    M&M Caps fit snug?

  48. lasse
    Date: Sun, Nov 9 2008 18:35:50

    Yes, they are as same as KT and CT Caps wink.gif

  49. Take-a-chill-pill
    Date: Sun, Nov 9 2008 18:39:31

    QUOTE (lasse @ Nov 9 2008, 06:35 PM) <{POST_SNAPBACK}>
    Yes, they are as same as KT and CT Caps wink.gif




    TO FAST REPLY mellow.gif And ty cause im gonna get duraflashes from Tomex and ill buy 2 M&M'S & 2 RSVP (BLK) From penwish biggrin.gif


    then ill need 2 save up for 2 dr. grip tips biggrin.gif

  50. giutyã…‹
    Date: Tue, Nov 25 2008 10:55:59

    oh i don't know that thanks

  51. Tekkai
    Date: Wed, Jan 14 2009 22:30:47

    Would Dong A caps work for this? Instead of the KT/CT they are much cheaper...

  52. Soulreaper
    Date: Wed, Jan 14 2009 22:34:58

    As already said, the comssa caps are too small, unless you want to do a lot of filing for the rsvp backplug (And I dont even know if the plug will file down so thin)

  53. enza99
    Date: Sun, Jan 18 2009 08:05:35

    much simpler than i thot =D
    i like how u dont have to stab holes anywhere... i always think about breaking it that way...
    btw just to say ive never made a mod, lol

    just needa c about that insert whatever thing... as like where to get... XD
    then i think ill get started on that =P

  54. Tekkai
    Date: Sun, Jan 18 2009 14:55:48

    So CT and KT caps work, right? But do you know where I can get just the caps? KT's are expensive.

  55. luke
    Date: Sun, Jan 18 2009 15:24:51

    QUOTE (Tekkai @ Jan 18 2009, 09:55 AM) <{POST_SNAPBACK}>
    So CT and KT caps work, right? But do you know where I can get just the caps? KT's are expensive.


    i dont think penwish sells only kt caps. you have to buy all the materials. but im sure some traders would be glad to trade some pre made caps..

  56. dhud470
    Date: Thu, Feb 26 2009 02:16:06

    Using an R.S.V.P is K4S's solution to everything.

  57. xSpin
    Date: Sat, May 2 2009 14:20:49

    my other backplug keeps wiggling, andy suggestions?

  58. webspider
    Date: Tue, May 5 2009 19:46:31

    Use hotglue to glue it on and wrap some tape around it. Then the Cap should fit tightly and nothing wiggles around anymore wink.gif

  59. jimmyfrostedflakes
    Date: Sat, May 9 2009 16:37:56

    can you show how to make a clear buster cyl i already have the clear kt

  60. JoeNugget
    Date: Sat, May 9 2009 17:31:50

    QUOTE (jimmyfrostedflakes @ May 9 2009, 12:37 PM) <{POST_SNAPBACK}>
    can you show how to make a clear buster cyl i already have the clear kt


    I dont think so, becasue comssa caps dont fit on rsvp backcaps. I remember seeing people use Mujis to make clear buster cyls

  61. lllllll7777777
    Date: Sun, Nov 22 2009 20:23:01

    this mod is kool! instead of using kt caps can u sub it 4 ct caps?

  62. iamk34n3
    Date: Sun, Nov 22 2009 20:33:54

    Yes, CT and KT caps are the same thing.

  63. strat1227
    Date: Thu, Feb 18 2010 13:29:45

    Second Picture is Dead sad.gif

    Kinda the hardest part in the whole tut lol

  64. XYZakiメAM
    Date: Thu, Feb 18 2010 14:25:14

    QUOTE (strat1227 @ Feb 18 2010, 05:29 AM) <{POST_SNAPBACK}>
    Second Picture is Dead sad.gif

    Kinda the hardest part in the whole tut lol


    This mod is basically just cutting off the end of an RSVP.

  65. AIRAZOR
    Date: Sun, Apr 25 2010 02:49:13

    QUOTE (K4S @ Oct 5 2007, 07:41 PM) <{POST_SNAPBACK}>
    Welcome to the Simple Clear body Dr.KT tutorial!

    A mini tutorial by me, K4S smile.gif

    I've seen many threads asking how to make a clear Dr.KT and the answer to that question is either find clear keityo or find a persons's pens or find pen XYZ etc, all of which are generally rare or difficult to get. This tutorial will provide an effective and simple solution to making a Clear Dr.KT.

    I've known about this for a long time, sorry, one of the many mini mods & variations to be forever stored in my secret box of pen mods ph34r.gif But it's thanksgiving weekend and I had some time to spare so I decided to make this tutorial.

    I never realised until I measured it but this mod (if made correctly) is 0.1mm longer than a real Dr.KT. As well, the diameter of a Keityo barrel (measured in the middle of the body) is 9.75mm and the "substitute" barrel (measured from the middle of the body) is 9.70mm, so you cynics don't have much to complain about, mmmkay?

    Stats:
    -pretty much the same as a Dr.KT happy.gif


    So let us begin�

    1.
    You will need:
    1x bare rsvp barrel
    2x rsvp back caps
    2x pre-made Dr.KT caps (Keityo + sailor grips + dr.grip tip)

    2.
    Get the rsvp body and follow the directions on the picture. The bottom rsvp body is what it should look like once cut, and make sure you get it under 0.6cm (0.5cm will do) or else the back cap wont fit on it properly.


    Spoiler:


    3.
    The cap should be very snug. It should not be able to wiggle around.

    Spoiler:


    4.
    The order in which to do the following has been numbered 1-4, you can follow along, right?

    Spoiler:



    Final Product!

    Spoiler:

    Close up of insert 1
    Close up of insert 2





    Trouble Shooting Questions:
    Q: I screwed on the back cap on the side with tape, put the dr.KT cap on, but when I went to take the Dr.KT cap off the rsvp back cap got pulled out as well and is stuck inside the Dr.KT cap. How do I get it out?
    A: Take another rsvp body, screw on the body to the back cap stuck in the dr.KT cap and then pull it out.

    Q: How durable is the side where the back cap screws onto tape?
    A: Durable enough for regular spinning unless you plan to practice leguining it against a wall.

    Q: wtf, secret box of mods?
    A: Uh huh, I'll release some of the stuff I have in there eventually...maybe ._.

    Q: Thank you!
    A: Not a question, but you're welcome happy.gif

    A: The answer is, This is awesome!�
    Q: What is a clear body dr.KT� tutorial? /vain

    Q: Post your insert NAO!!!!!
    A: *cries* ALL YOU PEOPLE WANT IS MORE MORE MORE MORE MORE *sobs* LEAVE ME ALONE *cries* YOU�RE LUCKY I EVEN MADE THIS TUTORIAL FOR YOU BASTARDS! *cries some more* LEAVE ME ALONE *cue more crying*

  66. Chief_Snake
    Date: Sun, Apr 25 2010 02:57:01

    this point of your post was....?

  67. Colin
    Date: Sun, Apr 25 2010 03:03:56

    QUOTE (Chief_Snake @ Apr 24 2010, 07:57 PM) <{POST_SNAPBACK}>
    this point of your post was....?

    the point of YOUR post was?


    Anyways, its exactly what XYZaki said.
    It is just an RSVP body, cut to accommodate two backplugs on both sides, so that 2 LARGE KT/CT caps will fit on. small caps will not.

    measurements are not down to the decimals, but they do, however, need to be precise enough

  68. Nation
    Date: Sun, Jun 20 2010 00:33:38

    QUOTE (Colin @ Apr 24 2010, 10:03 PM) <{POST_SNAPBACK}>
    the point of YOUR post was?


    Anyways, its exactly what XYZaki said.
    It is just an RSVP body, cut to accommodate two backplugs on both sides, so that 2 LARGE KT/CT caps will fit on. small caps will not.

    measurements are not down to the decimals, but they do, however, need to be precise enough

    make the cut off side the same length as the threads, which also means you can use the front for an SBV