UPSB v3

Tutorials Pending Approval / MP MX V.3

by: iamk34n3

  1. iamk34n3
    Date: Sat, Apr 4 2009 03:38:05







    First of all, all of the credit goes to TEK for figuring out how to make a MP MX without cutting the body. Because of this, the mod is a lot more stable, and is overall easier to make.

    So I am making this tutorial because it seems that quite a number of people want to know how to make this, and most importantly its Spring Break and I'm bored. xD

    Note: I didn't have extra parts to make another, so I just took apart my original mod.

    I would add basic stats here, but it is exactly the same as a normal mx.

    Anyways, here are the materials you will need:



    1x RSVP
    1x HGG
    1x Papermate Phd multi (can be subbed with papermate extend multi)
    1x Dr. Grip mechanism (optional)

    All measurements in the tutorial are the ones I used, they may not work for you!!

    Step 1:

    Remove the grip from the rsvp and the back plug and inktube as well.



    Step 2:

    Cut .5 centimeters from the tip of the rsvp



    Step 3:

    Empty out the rsvp inktube. (remove the tip, flush all the ink out) (I used a dr grip mechanism because I find emptying an inktube too messy. In addition, the lead may stick to the sides, so overall using a mechanical pencil mechanism is best.)

    Step 4:

    Tape the inktubes together



    Step 5:

    Drill a hole in the rsvp backplug so that the mechanism can move freely



    Step 6:

    Screw on the HGG tip to the front of the rsvp

    Step 7:

    Now here is the tricky part. What you want to do is to put a bunch of tape on the mechanism so that when you push down, the mechanism does not slide back. So basically wrap a bunch of tape, screw on the rsvp backplug, and push down on the tip and see if the inktube slides back. If it does, add more tape a little higher up. If you cannot screw the rsvp backplug on, take off some of the tape on the end. Here is a picture of where I taped it for reference:



    P.S. thats centimeters btw

    Step 8:

    Put the HGG backplug on the end of the inktube. If its too loose, then add some more tape on the end. Slide the RSVP grip into the cap and put the rsvp cap on the back of the rsvp. If the rsvp cap does not line up with the rsvp backplug, cut the inktube a bit and try again.



    Slide the HGG grip onto the front and you're done. =)

  2. Pencell
    Date: Sat, Apr 4 2009 03:40:55

    Lol, i didn't think it was to hard to figure out how to make it. But whatever. good tutorial.
    You might want to say if the COG is shifted or any other stat that isn't exactly the same as a MX

  3. dori
    Date: Sat, Apr 4 2009 04:24:28

    Aww you released the tut XD
    oh well at least now people will be happy~ smile.gif

  4. IlbiStarz
    Date: Tue, Apr 14 2009 03:56:10

    What is the PaperMate PHD Multi? Where can you find it and can it be subbed?

  5. shoeman6
    Date: Tue, Apr 14 2009 13:09:31

    Yes many simple (much cheaper) mechanical pencils use the same exact mechinism.
    You could probably find some pencils like that as low as 50cent

  6. BlacknWhite
    Date: Wed, Apr 15 2009 13:41:10

    oh wtf happened here lols. tons of peoples post were deleted o_O. anyways daiso sells a cheap phd multi sub. its called "double action" or something like that.