UPSB v3

Tutorials Pending Approval / Ultra R-Stic EX+

by AllenMuff

AllenMuff
Date: Wed, May 5 2010 03:20:41

Hey this is my first mod, it's pretty easy to make. Credits to Thnikk for the idea of the base from the R-Stic. I just made it heavier, writable, and made it look cooler .

-----------------------------------------------------

Ultra R-Stic EX+

COG=COP

Length= 22.7cm

Weight=BICtory < Ultra R-Stic EX+ < RSVP MX (slightly lighter than RSVP MX)

Style= Double Sided

Writable on both sides

$7-10? Something like that....i found all the materials on the ground xD

----------------------------------------------------

PENS NEEDED:

(2) Pilot G-2 Grips
(2) Foray Mechanical Pencils Tips (look at pic.)

(2) Ultra Round Stic Grip
----------------------------------------------------------

Spoiler:

Take apart pens and discard/save the parts you don't need. I only had one G2 grip and one foray mech pencil in the picture, but you need two.

Spoiler:

Take apart both Ultra Round Stic Grips. Keep one barrel and take out the back plug of the barrel you kept.

Spoiler:

Cut both Ultra Round Stic Grips' ink tube 1/2 cm from the back.

Spoiler:

Insert the front part of the Ultra Round Stic Grip with the inktube into one side of the barrel. Do the same with the other side. Both inktubes should be inside the barrel on top of each other.

Spoiler:

Now take the cap of the Ultra Round Stic Grip and break off the clip. Do the same with the second cap.

Spoiler:

Take a G2 grip and cut where the last ring is, or the red line shown in the picture. Do the same with the second G2 grip.

Spoiler:

Take the cap, and put the grips on as shown in the picture. Put the non ring part of the grip over the broken clip part on the cap, push it over until it covers the broken clip part, as shown in the picture. You want to leave a little bit of that part of the grip hanging out, so it keeps the cap on tighter and covers the Ultra round stic grip. Put the grip on from the BOTTOM of the cap, it's a lot easier. Then put the ringy part of the grip from the top of the cap down and leave plenty of room for the tip, the grip can be adjusted after you put the tip on. Do the same with the second cap.

Spoiler:

Now, take off the Foray mechanical pencil tip and screw it on the top part of the Ultra Round Stic Grip cap. You can use teflon tape, but i just smashed it on lol...it might seem slightly uneven but adjust it, and then screw it on tighter. When the tip is screwed on, adjust the ringy part of the grip right below the tip. Do the same with the second cap.

Spoiler:

Put the caps on the pen and your done!

-----------------------------------

Q&A

Q: What about an insert?
A: Idk if you can put inserts because of the two inktubes, but you can put an outsert. Personally i don't like outserts or inserts....they bother me haha.

-----------------------------------
Comments? Advice? Improvements?
Nachoaddict
Date: Wed, May 5 2010 03:32:52

Bictory + tips?

It seems a bit long and doesn't look too great. I wouls suggest working on aesthetics and then finding something to give this mod a unique feel, spinning effect, or something else
darkrose
Date: Wed, May 5 2010 03:35:04

actually r-stic is by pendolsa not thinkk
Colin
Date: Wed, May 5 2010 03:41:45

QUOTE (darkrose @ May 4 2010, 08:35 PM) <{POST_SNAPBACK}>
actually r-stic is by pendolsa not thinkk

Thnikk made a tutorial for the r-stic
AllenMuff
Date: Wed, May 5 2010 04:23:40

QUOTE (Nachoaddict @ May 4 2010, 08:32 PM) <{POST_SNAPBACK}>
Bictory + tips?

It seems a bit long and doesn't look too great. I wouls suggest working on aesthetics and then finding something to give this mod a unique feel, spinning effect, or something else

oh. ok i think this mod looks pretty good tho haha it was my first mod so wateverrr
neix
Date: Wed, May 5 2010 04:34:36

i just made it, it spins amazing! my new favorite mod! thankyou for the tut! its just as good as the 1337 mx!!
Nation
Date: Wed, May 5 2010 20:11:39

this isn't a new mod. it's a bictory.
AllenMuff
Date: Thu, May 6 2010 02:02:05

QUOTE (Nation @ May 5 2010, 01:11 PM) <{POST_SNAPBACK}>
this isn't a new mod. it's a bictory.

oh whoops i posted the wrong first pic haha....i accidently posted the first prototype i made....its supposed to be the ultra round stic grip as a barrel. and also the bictory isnt as long
Nation
Date: Thu, May 6 2010 16:15:59

QUOTE (AllenMuff @ May 5 2010, 09:02 PM) <{POST_SNAPBACK}>
oh whoops i posted the wrong first pic haha....i accidently posted the first prototype i made....its supposed to be the ultra round stic grip as a barrel. and also the bictory isnt as long

okay, it's an ugly, longer bictory.